CONTROL BOXES - Control Boxes are rated in Volts and Amps. Maximum peak watt motor usage is typically found by multiplying volts times amp rating when amps given is peak amp rating. Sustained wattage can be found by multiplying volts times run amp rating. In general when you see a wattage rating shown that is less than the product of multiplying the amps and volts it means the amps rating is the peak or maximum rating the control box can safely handle during acceleration from a stop or such loads. The normal operating amperage can be found by dividing the given wattage in this case by the voltage. No returns due to the nature of this device. Installation is suggested by a competent person using care to avoid misconnection that will cause a defect.HOW TO SELECT THE BEST CONTROL BOX FOR YOUR REPLACEMENT: These control boxes were selected for maximum universal replacement of almost all scooters as quality devices. To determine the best replacement you should first consider the voltage of your scooter where the number of 12 volt batteries yields the total voltage when combined (e.g., three batteries will be 36 volts). The wattage of the motor the controller will provide power to so that a 350 watt motor would need a control box capable of at least 350 watts output or more. Controller wattage can be higher than the motor wattage and make the controller less likely to overheat or burn out. You should also consider the connectors your existing control box has to the component harnesses so that you might be able to simply plug in the new control box (e.g., if your scooter has a six pin connector for the throttle/brake lever/speed indicator then that would be preferable to a control box with separate connectors for the throttle and brake lever). And you need to consider whether you have room for the size of the new control box in the area of your old control box. Connector problems can be overcome by using a replacement universal conector package we sell on this page if it comes to that and the connector set is not expensive. And most scooters can accomodate a larger control box. Also, do look at the Wiring Connection diagrams and information links provided in the part descriptions, and be sure to mark your connectors as they are used for the different components in your scooter (e.g., throttle, switch/lock, brake lever, brake light, charger socket, on/off power indicator light, motor, and battery set.
X-TREME X-10 100 Watt Control Box - $31.95
plus shipping/handling.
No returns or exchanges due to the nature of this device. Installation is suggested by a competent person using care to avoid misconnection that will cause a defect.
Wiring diagram
HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC
Control Box For Vapor Scooter $19.95
plus shipping/handling - When Available Only Wiring diagram Pin ID Picture. Replacement control box using the same small pin connectors for Vapor scooters and others of the same type. Plug in and go. The Vapor may also be called Tornado and other names.
No returns or exchanges due to the nature of this device. Installation is suggested by a competent person using care to avoid misconnection that will cause a defect.
HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC
Control Box for X11 or X-250, 250 watt motor, 30 Amp, 24 Volt $39.95
X-11
No returns or exchanges due to the nature of this device. Installation is suggested by a competent person using care to avoid misconnection that will cause a defect.
HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC
30 AMP 24 VOLT CONTROLLER for Motors up to 300 WATT - $25.95
plus shipping/handling
-
Wiring connection, LB27, 300 Watt or less Scooter Replacement at 10 normal amps to 30 amps peak. 3.25"L X 2.25"W X 1.35"H. Small size for tight spot location. 20.5 volt under voltage protection extends battery life. Harness wiring supports key switch, brake indicator, power indicator, charger connector, 3 wire throttle, brake lever cutout switch cuts battery output, motor, and battery. Some wire splicing may be necessary in some applications.
Tested prior to packaging. No returns or exchanges due to the nature of this device. Installation is suggested by a competent person using care to avoid misconnection that will cause a defect.
30 AMP 24 VOLT CONTROLLER for Motors up to 500 WATT - $28.95
plus shipping/handling
-
Wiring connection, CT-302S9, 400 Watt or less, 10.5 normal amps to peak 30 amps. 4.25"L X 2"W X 1.4"H. Small size for tight spot location. Current limiting avoids damage to the motor and controller. Under voltage protection extends battery life. Over speed prevention while charging (renders the throttle temporarily inoperable to prevent mistaken manipulation). Harness wiring supports key switch, brake indicator, power indicator, charger connector, 6 wire for throttle/brake lever/speed indicator, motor, and battery. Some wire splicing may be necessary in some applications.
Tested prior to packaging. No returns or exchanges due to the nature of this device. Installation is suggested by a competent person using care to avoid misconnection that will cause a defect.
30 AMP 24 VOLT CONTROLLER for Motors up to 500 WATT - $29.95
plus shipping/handling
-
Wiring connection, CT-811B9 or CT-803B9 (no speed wire), 7 connector, 500 Watt or less, 10.5 normal amps to peak 30 amps. 4.35"L (3.2"L not including mounting tabs) X 3"W X 1.3"H. Small size for tight spot location. Current limiting avoids damage to the motor and controller. Under voltage protection extends battery life. Over speed prevention while charging (renders the throttle temporarily inoperable to prevent mistaken manipulation). Harness wiring supports key switch, brake indicator, power indicator, charger connector, 6 wire throttle/brake lever/speed indicator (no speed wire on CT-803B9), motor, and battery. Some wire splicing may be necessary in some applications.
Tested prior to packaging. No returns or exchanges due to the nature of this device. Installation is suggested by a competent person using care to avoid misconnection that will cause a defect.
30 AMP 24 or 36 VOLT CONTROLLER 500 WATT - $39.95
plus shipping/handling
-
Wiring connection, JC-116, 24 or 36 Volt 500 Watt or less Scooter Replacement at 30 amps. Small size for tight spot location, 3.25L, 2.5W, 1.25H. Mounting bracket along back edge. Current limiting avoids damage to the motor and controller. Under voltage protection extends battery life. 8 connector harness wiring supports key switch, battery capacity, charger connector, 3 wire throttle (this is one of the few 36 volt controllers with a three pin connector for the throttle), brake lever cutout switch cuts battery output, stop light, motor, and battery. Some wire splicing may be necessary in some applications.
Tested prior to packaging. No returns or exchanges due to the nature of this device. Installation is suggested by a competent person using care to avoid misconnection that will cause a defect.
30 AMP 24 VOLT CONTROLLER for Motors up to 750 WATT - $29.95
plus shipping/handling
- Wiring connection, LB14 / LBD14, 750 Watt or less, 10.5 normal amps to peak 30 amps. 3.5"L X 2.75"W X 1.5"H. Small size for tight spot location. Seven connectors. Current limiting avoids damage to the motor and controller. Under voltage protection extends battery life. Over speed prevention while charging (renders the throttle temporarily inoperable to prevent mistaken manipulation). 8 wire harness supports key switch, brake signal, power indicator, charger connector, 3 wire throttle, brake lever cutout switch cuts battery output, motor, and battery. Some wire splicing may be necessary in some applications.
Tested prior to packaging. No returns or exchanges due to the nature of this device. Installation is suggested by a competent person using care to avoid misconnection that will cause a defect.
HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC
500-950 WATT 24 or 36 VOLT 30 AMP REVERSABLE CONTROLLER $64.95
plus shipping/handling This controller has 8 connects. Rated Voltage 24 or 36 Volts. Max Current 30 Amps. Usable Motors: 500+ Watts. 4"L X 2.75"W X 1.5"H.
Rated Voltage: 24 or 36 Volts, Rated Motors 500+ watts, Rated Current to 30 amps, Conversion Efficiency: 95%, Under voltage protection: 20.5 volts or 31, Speed control: Hall effect Turn or thumb throttle, Brake Indicator, Power Indicator, 3 Wire Lock/Switch Connector with Forward or Reverse function, Charger connector, Pilot Light connector, Brake Lever cut-out connector, Motor and Battery connectors. Possible easy mount switch assembly for use in forward and reverse control is our
handlebar mounted switch assembly or
three position key switch sold below.
Current Limiting prevents motor current from exceeding the specified value and avoids damage to the motor and control box due to over current conditions. Under voltage protection when the battery voltage falls to specified value, cutting battery output and preventing over discharge which extends battery life. Over speed prevention while charging renders the throttle temporarily inoperable and prevents mistaken operation. Power cut-off during braking.
Simple connector plugs use or splice of harness wires to existing scooter wiring from control box or to components.
Tested prior to packaging. No returns or exchanges due to the nature of this device. Installation is suggested by a competent person using care to avoid misconnection that will cause a defect.
Wiring Connection
HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC
30 AMP 600 WATT 24 VOLT HEAVY DUTY CONTROLLER - $54.95
plus shipping/handling (5L X 3.5H X 2H). YK42-2. This 30 amp controller is a replacement for electric Scooters using up to 600 watt 24 volt motors wired similar to the Rad2Go E10 Scooter. Easy splice wiring harness. Just connect to motor, 3 wire connector for hall effect throttle, and then 36 volt battery set through a switch for high quality and endurance you need.
Tested prior to packaging. No returns or exchanges due to the nature of this device. Installation is suggested by a competent person using care to avoid misconnection that will cause a defect.
Wiring diagram
HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC
20 Amp 36 Volt Control Box for X360 350-500 watt motor and other scooters $59.95
Replacement controller (brain) for 36 volt model X-360. In the X360 this control box replaces your controller when you EMAIL US INFORMATION ABOUT YOUR INSTALLED CONTROL BOX as indicated at this link that provides troubleshooting help. USE THE FOLLOWING INFORMATION TO DETERMINE THE VERSION NUMBER AND SELECT IT ON THE ORDER MENU BEFORE ADDING THE ITEM TO THE SHOPPING CART.
Tested prior to packaging. No returns or exchanges due to the nature of this device. Installation is suggested by a competent person using care to avoid misconnection that will cause a defect.
VERSION 2 Upgraded replacement controller (brain) for 36 volt model X-360. This item can also work in all other 36 volt scooters but may require modification to the wire harness. This item replaces all 08/20/2003 make date controllers with 10 connectors on the controller. This item also replaces a controller with a Version 2 Upgraded sticker on it
VERSION 3 Upgraded replacement controller (brain) for 36 volt model X-360. This item can also work in all other 36 volt scooters but may require modification to the wire harness. This item replaces all 09/30/2003 make date controllers & some 8/20/2003 controllers
VERSION 4 Upgraded replacement controller (brain) for 36 volt model X-360. This item can also work in all other 36 volt scooters but may require modification to the wire harness. This item replaces controllers made after 11/01/2004
VERSION 5 Upgraded replacement controller (brain) for 36 volt model X-360. This item can also work in all other 36 volt scooters but may require modification to the wire harness. This item replaces controllers made after Mid 2005
Wiring Connection
Wiring diagram PDF
Wiring diagram JPG
Wiring diagram Dash JPG
[NOTE: WIRING MAY BE DIFFERENT FOR THE X360 DEPENDING ON THE CONTROL BOX VERSION AND YEAR OF MAKE]
HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC
350-500 watt 36 Volt Control Box $39.95
Replacement controller (brain) for 36 volt 350 watt motors. 4.25"L X 2"W X 1.4"H. Connectors for Battery, Motor, 6 wire connector for standard three wire throttle, brake lever, and speed control. Plus switch, charger socket, and Brake light connectors. No returns or exchanges due to the nature of this device. Installation is suggested by a competent person using care to avoid misconnection that will cause a defect.
Wiring Connection
Wiring diagram PDF
HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC
750-1000 Watt 36 Volt 40 Amp Controller for up to 750 Watt 36 Volt Motors $49.95
plus shipping/handling CT-660B8. This controller has 8 connectors. Rated Voltage 36 Volts. Max Current 40 Amps. Usable Motors: up to 1000 Watts.
3.5"L X 2.5"W X 1.5"H. Rated Voltage: 36 Volts, Rated Motors to 1000 watts, Rated Current to 40 amps, Conversion Efficiency: 95%, Under voltage protection: 31.5 volts, 4 wire connector has a speed indicator wire plus standard 3 wire for throttle, Brake Light Indicator, Power Indicator, Brake lever cut-out, Charger Connector, Lock/switch connector, Motor and Battery connectors.
Current Limiting prevents motor current from exceeding the specified value and avoids damage to the motor and control box due to over current conditions. Under voltage protection when the battery voltage falls to specified value, cutting battery output and preventing over discharge which extends battery life. Over speed prevention while charging renders the throttle temporarily inoperable and prevents mistaken operation. Power cut-off during braking.
Simple connector plugs use or splice of harness wires to existing scooter wiring from control box or to components.
Tested prior to packaging. No returns or exchanges due to the nature of this device. Installation is suggested by a competent person using care to avoid misconnection that will cause a defect.
Wiring Connection
HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC
1000 Watt 36 Volt 40 Amp Controller for up to 1000 Watt 36 Volt Motors $59.95
plus shipping/handling CT-660B9. This controller has 7 connectors. Rated Voltage 36 Volts. Max Current 40 Amps. Usable Motors: up to 1000 Watts. Diminsions: 5"L X 3"W X 1.5"H
Rated Voltage: 36 Volts, Rated Motors to 1000 watts, Rated Current to 40 amps, Conversion Efficiency: 95%, Under voltage protection: 31.5 volts, 6 wire connector for throttle/brake lever/speed indicator, Brake Light, Power Indicator, Charger Connector, Lock/Switch connector, Motor and Battery connectors.
Current Limiting prevents motor current from exceeding the specified value and avoids damage to the motor and control box due to over current conditions. Under voltage protection when the battery voltage falls to specified value, cutting battery output and preventing over discharge which extends battery life. Over speed prevention while charging renders the throttle temporarily inoperable and prevents mistaken operation. Power cut-off during braking.
Simple connector plugs use or splice of harness wires to existing scooter wiring from control box or to components.
Tested prior to packaging. No returns or exchanges due to the nature of this device. Installation is suggested by a competent person using care to avoid misconnection that will cause a defect.
Wiring Connection
HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC
36 Volt Digital Heavy Duty Controller for up to 40 amps and up to 1000+ Watt Motors. $59.95
plus shipping/handling YK42-3 - A great buy on this heavy duty simple 40 amp control box for up to 1000+ watt electric 36 volt motors. Just connect to motor, 3 wire connector for hall effect throttle, and then 36 volt battery set through a switch for high quality and endurance you need. 7.5"L X 3.5"W X 2"H. For scooters with wiring similar to the Rad2Go E36 Great White Scooter.
Tested prior to packaging. No returns or exchanges due to the nature of this device. Installation is suggested by a competent person using care to avoid misconnection that will cause a defect.
Wiring Connection
HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC
48 Volt Digital Controller up to 1500+ Watt Motors at 50 amps $74.95
plus shipping/handling LB37 - for up to 1500+ watt electric motors. 7 wire connector harness supports key switch, charger connector, 3 wire throttle, brake lever cutout switch cuts battery output, power indicator light, motor, and battery. 4.5"L X 2.75"W X 1.5"H.
Tested prior to packaging. No returns or exchanges due to the nature of this device. Installation is suggested by a competent person using care to avoid misconnection that will cause a defect.
Wiring Connection
HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC
48 Volt Digital Heavy Duty Controller for up to 100 amps and 2000+ Watt Motors. $89.95
plus shipping/handling YK42-4 - A great buy on this heavy duty simple 40 - 100 amp control box for up to 2000+ watt electric 48 volt motors. 6"L X 3.5"W X 2"H. Just connect to motor, 3 wire connector hall effect throttle, and then 48 volt battery set for high quality and endurance you need.
Tested prior to packaging. No returns or exchanges due to the nature of this device. Installation is suggested by a competent person using care to avoid misconnection that will cause a defect.
Wiring Connection
HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC
48 Volt Digital Heavy Duty Controller for Hub Motors. $89.95
plus shipping/handling when available (a rare item) - Heavy duty control box that fits hub motors scooters like the Panterra (Freedom electric), Panterra (Fusion electric), Panterra (Retro Electric), and
X-Treme
No returns or exchanges due to the nature of this device. Installation is suggested by a competent person using care to avoid misconnection that will cause a defect. Other Hub Motor control boxes may work as a substitute when this one is not available (example - try the XB-600 or XB-700 control box)
MATCHING 750 WATT HUB MOTOR -
48 VOLT TO 12 VOLT CONVERTER
HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC
CONVERTER 30-60V TO 12V DC - $21.95
plus shipping/handling - 3-pin connection, Wire colors: Red, Yellow and Black, DC481213, DC 30V-60V to DC 12V / 10A, Measures 3 x 3 x 1 1/4"Supported Models: Various unlisted makes/models, Panterra (Freedom electric), Panterra (Fusion electric), Panterra (Retro Electric), X-Treme
HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC
SIX CONNECTOR SET FOR SCOOTERS - $6.95
plus shipping/handling - Universal set of Scooter Connectors. Six male and female connector sets: two, three, four, six pins, 2 pin motor, and battery 2 pin connector sets. Makes installation of control boxes easier.
HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC
SCOOTER ELECTRICAL
