Throttles, Controllers, Control Boxes, Battery Chargers, Batteries, Brake Levers, Switches, Key Switches, On Off and Kill Switches, Fuses and Fuseholders, Lighting and Signals, General and Common Scooter Electrical Components, All Scooter Electric Parts, All Scooter Support, and Most Scooter Parts

X360 Blinker Module $7.95

For use in X360 and many other 36 volt scooters

HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

X-10 and X-140 24V Battery Charger, replaces old style Battery Charger which was prone to failure and overcharged batteries. New Intelligent X-10 and X-140 scooter battery chargers automatically charge batteries at a rate that will not damage batteries and shuts off to prevent overcharging or charger failure - High Quality, same single pin connector for X-10/X-140 Scooter - $19.95

plus shipping/handling
3.5mm Single pin female connection to scooter charger input port.

HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

Battery Charger INPUT PORT - $9.95
plus shipping/handling Regular $14.95
3.5mm Single pin male connector receptacle for x010 Battery Charger input.

HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

CONNECTOR PLUG, 3.5MM - $7.95
plus shipping/handling. Regular Retail Price less shipping $14.95
3.5mm Single pin female connector plug for x010 and other scooters Battery Charger input.

HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

3 prong Female Plug, 12 Volt Battery Charger For Scooters with three prong male socket Receptacles (90-245V AC with 16.5V DC 1.0A Output) $17.95
plus shipping/handling

Intelligent Battery Charger provides current to battery set at correct amount to charge without overheating, shut off when batteries are charged.
HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC Parts are inspected and tested prior to packaging

24 volt, two prong Battery Charger
for the model X-11 x-treme scooter and others $35.95
Plus Shipping/Handling

Intelligent charger provides current to battery set at correct amount to charge without overheating, shut off when batteries are charged. Indicator light shows charging and when charged. Standard 3 prong 24v Charger and 3 pin socket can also be used when you replace the socket on the scooter.

HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

24 Volt Battery Charger, 3 Prong Plug. $16.95
(90-245V AC with 29.5V DC 1.6 Amp Output)
Use with all 24 volt, 3 prong scooters with either standard female connector or XLR Male Connector. This charger is superior to most sold scooter chargers because it has a fuse that can be changed if blown due to overload or short. The case can be opened, unlike most others, and the fuse replaced. But if your socket is different it can still be used by replacing the socket on the scooter. Need a socket? See it available separately.
plus shipping/handling

Charger indicates red when charging and green when fully charged. May be used with two prong Battery Charger connectors by using the old two prong plug from the previous Battery Charger. Only two of the three pins are used in three prong chargers (pin 1 is always positive).
HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC Parts are inspected and tested prior to packaging

24 Volt, 3 Prong Male XLR Connector - $34.95
(100-240V AC with +24V DC 1.6 Amp Output)
plus shipping/handling

24 volt, three MALE prong Battery Charger as used on many Scooters including Schwinn, Mongoose, GT, and Currie. Charger with indicator light shows when charging and fully charged. Matches socket below.

HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

Battery Charger, Europe Plug, 24 Volt, 3 Prong Female Plug. $19.95
(90-245V AC with 29.5V DC 1.6 Amp Output)
Use with AC oulets in Europe. For all 24 volt, 3 prong scooters with 3 pin male sockets. This charger is superior to most sold scooter chargers because it has a fuse that can be changed if blown due to overload or short. The case can be opened, unlike most others, and the fuse replaced. But if your socket is different it can still be used by replacing the socket on the scooter. Need a socket? See it available separately.
plus shipping/handling

36 volt, two prong Battery Charger for X360 and other scooters with 2 or 3 prong male sockets on the scooter. $34.95
Plus Shipping and Handling
Intelligent Battery Charger provides current to battery set at correct amount to charge without overheating, shut off when batteries are charged. Indicator light shows red during charge, green when charged. The X360 also now comes with a 3 pin charger socket, your choice of two or three pin below. Standard 3 prong 36v Charger AND a new 3 pin socket can also be used when you replace the socket on the scooter on X360 scooters with a 2 pin socket.

HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

36 Volt Battery Charger, 3 Prong Connector For $18.95
(90-245V AC with 42.6V DC 1.6 Amp Output)
plus shipping/handling

36 volt, three prong Battery Charger with either standard female connector or XLR Male Connector. Charger with indicator light shows when charging and fully charged. May be used with two prong Battery Charger connectors by using the old two prong plug from the previous Battery Charger. Or purchase the three prong socket below for replacement to match this Battery Charger connector.

HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

Battery Charger Receptacle, two prong male $16.95
for X-treme X11, X360 models and many others.
Plus shipping/handling.

HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

3 Prong Battery Charger Plug
Replaces the standard female or male XLR plug on the Scooter Battery Charger cord $11.95
plus shipping/handling
Standard female three pin Scooter Battery Charger plug of most Electric Scooters including Rad2Go, Razor, Vapor and X-treme Scooters.

HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

3 Prong Battery Charger Receptacle.
Replaces the male receptacle on the Scooter $7.95
plus shipping/handling
Standard male 3 pin receptacle socket to receive the female three pin Battery Charger plug of most Electric Scooters including Vapor Scooters. Replacement for any make Scooter, may require splicing to your existing wiring connectors to your control box.

HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

36 Volt, 3 Prong Male XLR Connector - $39.95
(100-240V AC with 41.8V DC 1.6 Amp Output)
plus shipping/handling

36 volt, three MALE prong Battery Charger as used on many Scooters including some X-treme Models, MX500, etc. Charger with indicator light shows when charging and fully charged. Matches socket below.

HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

3 Prong Female Socket For $11.95

plus shipping/handling

HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

48 Volt 2.5 Amp Fan Cooled Battery Charger, Choice of Panterra Polarity or Reversed Polarity PC Style Female Connectors, $79.95
plus shipping/handling

Intelligent 48 volt, three prong PC Style connector plug, Fan Cooled, Intelligent Battery Charger with 100-240V AC with 53.5V DC 2.5 Amp Output. Charger with two indicator lights show when charging and fully charged. Polarity for most Pantera scooters or reversed polarity.

HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

48 Volt 2.5 Amp Fan Cooled Battery Charger, Standard 3 Prong Round Connector, $79.95
plus shipping/handling

Intelligent 48 volt, three prong round female connector plug (matches the socket on this page), Fan Cooled, Intelligent Battery Charger with 100-240V AC with 53.5V DC 2.5 Amp Output. Charger with two indicator lights show when charging and fully charged. If your socket is different it can still be used by replacing the socket on the scooter with the matching socket sold here, or by splicing or soldering on your old charger's plug. Plug polarity is indicated on the case of the charger as the normal Pin 1 positive (brown wire), Pin 3 Negative (blue wire), Pin 2 unused.

HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

Heavy Duty 48 Volt 5/6 Amp Battery Charger For $99.95
48V Fan Cooled Charger for large electric scooters like the Panterra. Amperage output is up to 6 Amps. Fast charge use for Panterra (Freedom electric), Panterra (Fusion electric), Panterra (Retro Electric), and Various makes/models of electric scooters of different connection polarities. Fan cooled for heavy duty use, fuse protected. Plus voltage at L (Load), minus voltage at N (Negative), and E is Empty or unused as indicated on the charger plug. Pretested in load environment for a 48 volt battery set. Also, a reversed polarity version of this same charger where N is positive voltage, and L is negative voltage (E is Empty), for many brands of scooters using this type connector.
plus shipping/handling Availability of this item?

HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

Heavy Duty 48 Volt 9 Amp Battery Charger For $129.95
48V Fan Cooled Charger for large electric scooters like the Panterra. Amperage output is up to 9 Amps. Fast charge use for Panterra (Freedom electric), Panterra (Fusion electric), Panterra (Retro Electric), and Various makes/models of electric scooters of different connection polarities. Fan cooled for heavy duty use, fuse protected. Plus voltage at L (Load), minus voltage at N (Negative), and E is Empty or unused as indicated on the charger plug. Pretested in load environment for a 48 volt battery set. Also, a reversed polarity version of this same charger where N is positive voltage, and L is negative voltage (E is Empty), for many brands of scooters using this type connector.
plus shipping/handling Availability of this item?

HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

Item # X500-250
Battery Charger 48 Volt
1.5 Amp Original Equipment
With cooling fan
3 Pin Female Connector
for our X500 Xtreme Scooter
but may be adapted to other 48 volt scooters
when the original connector is used or the
scooter socket on the scooter is replaced.

$58.95 Each plus shipping
Parts are inspected and tested prior to packaging

Item # XA-1000-250
Battery Charger, 3 PRONG, 60 VOLTS
X-treme ATV XA-1000 Scooter Charger

$58.95 plus shipping

CONTROL BOXES - Control Boxes are rated in Volts and Amps. Maximum peak watt motor usage is typically found by multiplying volts times amp rating when amps given is peak amp rating. Sustained wattage can be found by multiplying volts times run amp rating. In general when you see a wattage rating shown that is less than the product of multiplying the amps and volts it means the amps rating is the peak or maximum rating the control box can safely handle during acceleration from a stop or such loads. The normal operating amperage can be found by dividing the given wattage in this case by the voltage.

X-TREME X-10 100 Watt Control Box - $31.95
plus shipping/handling.
No returns due to the nature of this device. Installation is suggested by a competent person using care to avoid misconnection that will cause a defect.

Wiring diagram

HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

Control Box For Vapor Scooter $14.95 ON SALE!
plus shipping/handling

Wiring diagram
Pin ID Picture. Replacement control box using the same small pin connectors for Vapor scooters and same as type scooters. Plug in and go.
HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

VAPOR SUB CONTROL BOX - $19.95 WITH SHIPPING:

Control Box for X11, 250 watt motor, 30 Amp, 24 Volt $31.95

No returns due to the nature of this device. Installation is suggested by a competent person using care to avoid misconnection that will cause a defect.

HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

30 AMP 24 VOLT CONTROLLER for Motors up to 400 WATT - $25.95
plus shipping/handling

- Wiring diagram, 400 Watt or less Scooter Replacement at 10 normal amps to 30 amps peak. Small size for tight spot location. 20.5 volt under voltage protection extends battery life. Harness wiring supports key switch, brake indicator, power indicator, charger connector, throttle, brake lever cutout switch cuts battery output, motor, and battery. Some wire splicing may be necessary in some applications.
Tested prior to packaging. No returns due to the nature of this device. Installation is suggested by a competent person using care to avoid misconnection that will cause a defect.

30 AMP 24 VOLT CONTROLLER for Motors up to 500 WATT - $28.95
plus shipping/handling

- Wiring diagram, 500 Watt or less, 10.5 normal amps to peak 30 amps. Small size for tight spot location. Current limiting avoids damage to the motor and controller. Under voltage protection extends battery life. Over speed prevention while charging (renders the throttle temporarily inoperable to prevent mistaken manipulation). Harness wiring supports key switch, brake indicator, power indicator, charger connector, throttle, brake lever cutout switch cuts battery output, speed indicator, motor, and battery. Some wire splicing may be necessary in some applications.
Tested prior to packaging. No returns due to the nature of this device. Installation is suggested by a competent person using care to avoid misconnection that will cause a defect.

30 AMP 24 VOLT CONTROLLER 500 WATT - $39.95
plus shipping/handling

- Wiring diagram, 500 Watt or less Scooter Replacement at 30 amps. Small size for tight spot location, 3.25L, 2.5W, 1.25H. Mounting bracket along back edge. Current limiting avoids damage to the motor and controller. Under voltage protection extends battery life. Harness wiring supports key switch, brake indicator, battery capacity, charger connector, throttle, brake lever cutout switch cuts battery output, stop light, motor, and battery. Some wire splicing may be necessary in some applications.
Tested prior to packaging. No returns due to the nature of this device. Installation is suggested by a competent person using care to avoid misconnection that will cause a defect.

750 WATT 24 VOLT 30 AMP CONTROLLER $44.95
plus shipping/handling

This controller has 8 connects. Rated Voltage 24 Volts. Max Current 30 Amps. Usable Motors: up to 750 Watts. Rated Voltage: 24 Volts, Rated Motors up to 750 watts, Rated Current at 30 amps, Conversion Efficiency: 95%, Under voltage protection: 20.5 volts, Speed control: Hall effect Turn or thumb throttle, Brake Indicator, Power Indicator, Lock Connector, Charger connector, Pilot Light connector, Brake Lever cut-out connector, Motor and Battery connectors.
Current Limiting prevents motor current from exceeding the specified value and avoids damage to the motor and control box due to over current conditions. Under voltage protection when the battery voltage falls to specified value, cutting battery output and preventing over discharge which extends battery life. Over speed prevention while charging renders the throttle temporarily inoperable and prevents mistaken operation. Power cut-off during braking.
Simple connector plugs use or splice of harness wires to existing scooter wiring from control box or to components.
Tested prior to packaging. No returns due to the nature of this device. Installation is suggested by a competent person using care to avoid misconnection that will cause a defect.
Wiring Connection
HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

500-950 WATT 24 or 36 VOLT 30 AMP REVERSABLE CONTROLLER $64.95
plus shipping/handling

This controller has 8 connects. Rated Voltage 24 or 36 Volts. Max Current 30 Amps. Usable Motors: 500+ Watts. Rated Voltage: 24 or 36 Volts, Rated Motors 500+ watts, Rated Current to 30 amps, Conversion Efficiency: 95%, Under voltage protection: 20.5 volts or 31, Speed control: Hall effect Turn or thumb throttle, Brake Indicator, Power Indicator, Lock Connector with Forward or Reverse, Charger connector, Pilot Light connector, Brake Lever cut-out connector, Motor and Battery connectors. Possible easy mount switch assembly for use in forward and reverse control is our handlebar mounted switch assembly or three position key switch sold below.
Current Limiting prevents motor current from exceeding the specified value and avoids damage to the motor and control box due to over current conditions. Under voltage protection when the battery voltage falls to specified value, cutting battery output and preventing over discharge which extends battery life. Over speed prevention while charging renders the throttle temporarily inoperable and prevents mistaken operation. Power cut-off during braking.
Simple connector plugs use or splice of harness wires to existing scooter wiring from control box or to components.
Tested prior to packaging. No returns due to the nature of this device. Installation is suggested by a competent person using care to avoid misconnection that will cause a defect.
Wiring Connection
HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

30 AMP 600 WATT 24 VOLT HEAVY DUTY CONTROLLER - $54.95
plus shipping/handling

(3.5L X 2.5H X .75H). This 30 amp controller is a replacement for electric Scooters using up to 600 watt 24 volt motors wired similar to the Rad2Go E10 Scooter. Easy splice wiring harness.
Tested prior to packaging. No returns due to the nature of this device. Installation is suggested by a competent person using care to avoid misconnection that will cause a defect. Wiring diagram
HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

20 Amp 36 Volt Control Box for X360 350-500 watt motor and other scooters $31.95

Replacement controller (brain) for 36 volt model X-360. In the X360 this control box replaces your controller when you EMAIL US INFORMATION ABOUT YOUR INSTALLED CONTROL BOX as indicated at this link that provides troubleshooting help. USE THE FOLLOWING INFORMATION TO DETERMINE THE VERSION NUMBER AND SELECT IT ON THE ORDER MENU BEFORE ADDING THE ITEM TO THE SHOPPING CART.
Tested prior to packaging. No returns due to the nature of this device. Installation is suggested by a competent person using care to avoid misconnection that will cause a defect.

VERSION 2 Upgraded replacement controller (brain) for 36 volt model X-360. This item can also work in all other 36 volt scooters but may require modification to the wire harness. This item replaces all 08/20/2003 make date controllers with 10 connectors on the controller. This item also replaces a controller with a Version 2 Upgraded sticker on it

VERSION 3 Upgraded replacement controller (brain) for 36 volt model X-360. This item can also work in all other 36 volt scooters but may require modification to the wire harness. This item replaces all 09/30/2003 make date controllers & some 8/20/2003 controllers

VERSION 4 Upgraded replacement controller (brain) for 36 volt model X-360. This item can also work in all other 36 volt scooters but may require modification to the wire harness. This item replaces controllers made after 11/01/2004

VERSION 5 Upgraded replacement controller (brain) for 36 volt model X-360. This item can also work in all other 36 volt scooters but may require modification to the wire harness. This item replaces controllers made after Mid 2005

Wiring Connection
Wiring diagram PDF
Wiring diagram JPG
Wiring diagram Dash JPG

HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

750-1000 Watt 36 Volt 40 Amp Controller for up to 750 Watt 36 Volt Motors $49.95
plus shipping/handling

This controller has 8 connectors. Rated Voltage 36 Volts. Max Current 40 Amps. Usable Motors: up to 1000 Watts.
Rated Voltage: 36 Volts, Rated Motors to 1000 watts, Rated Current to 40 amps, Conversion Efficiency: 95%, Under voltage protection: 31.5 volts, Speed control: Hall effect Turn or thumb throttle, Brake Indicator, Power Indicator, Brake lever cut-out, Charger Connector, Lock connector, Motor and Battery connectors.
Current Limiting prevents motor current from exceeding the specified value and avoids damage to the motor and control box due to over current conditions. Under voltage protection when the battery voltage falls to specified value, cutting battery output and preventing over discharge which extends battery life. Over speed prevention while charging renders the throttle temporarily inoperable and prevents mistaken operation. Power cut-off during braking.
Simple connector plugs use or splice of harness wires to existing scooter wiring from control box or to components.
Tested prior to packaging. No returns due to the nature of this device. Installation is suggested by a competent person using care to avoid misconnection that will cause a defect.
Wiring Connection
HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

1000 Watt 36 Volt 40 Amp Controller for up to 1000 Watt 36 Volt Motors $59.95
plus shipping/handling

This controller has 7 connectors. Rated Voltage 36 Volts. Max Current 40 Amps. Usable Motors: up to 1000 Watts. Diminsions: 5"L X 3"W X 1.5"H
Rated Voltage: 36 Volts, Rated Motors to 1000 watts, Rated Current to 40 amps, Conversion Efficiency: 95%, Under voltage protection: 31.5 volts, Speed control: Hall effect Turn or thumb throttle, Brake Indicator, Power Indicator, Brake lever cut-out, Charger Connector, Lock connector, Motor and Battery connectors.
Current Limiting prevents motor current from exceeding the specified value and avoids damage to the motor and control box due to over current conditions. Under voltage protection when the battery voltage falls to specified value, cutting battery output and preventing over discharge which extends battery life. Over speed prevention while charging renders the throttle temporarily inoperable and prevents mistaken operation. Power cut-off during braking.
Simple connector plugs use or splice of harness wires to existing scooter wiring from control box or to components.
Tested prior to packaging. No returns due to the nature of this device. Installation is suggested by a competent person using care to avoid misconnection that will cause a defect.
Wiring Connection
HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

36 Volt Digital Heavy Duty Controller for up to 40 amps and up to 1000+ Watt Motors. $59.95
plus shipping/handling

- A great buy on this heavy duty simple 40 amp control box for up to 1000+ watt electric 36 volt motors. Just connect to motor, hall effect throttle, and then 36 volt battery set for high quality and endurance you need. For scooters with wiring similar to the Rad2Go E36 Great White Scooter.
Tested prior to packaging. No returns due to the nature of this device. Installation is suggested by a competent person using care to avoid misconnection that will cause a defect.
Wiring Connection
HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

48 Volt Digital Controller up to 1500+ Watt Motors at 50 amps $74.95
plus shipping/handling

- for up to 1500+ watt electric motors.
Tested prior to packaging. No returns due to the nature of this device. Installation is suggested by a competent person using care to avoid misconnection that will cause a defect.
Wiring Connection
HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

48 Volt Digital Heavy Duty Controller for up to 100 amps and 2000+ Watt Motors. $89.95
plus shipping/handling

- A great buy on this heavy duty simple 40 - 100 amp control box for up to 2000+ watt electric 48 volt motors. Just connect to motor, hall effect throttle, and then 48 volt battery set for high quality and endurance you need.
Tested prior to packaging. No returns due to the nature of this device. Installation is suggested by a competent person using care to avoid misconnection that will cause a defect.
Wiring Connection
HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

48 Volt Digital Heavy Duty Controller for Hub Motors. $89.95
plus shipping/handling

- A great buy on this heavy duty control box that fits hub motors scooters like the Panterra (Freedom electric), Panterra (Fusion electric), Panterra (Retro Electric), and X-Treme
No returns due to the nature of this device. Installation is suggested by a competent person using care to avoid misconnection that will cause a defect.
HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

CONNECTOR SET FOR SCOOTERS - $5.95
plus shipping/handling

- Universal set of Scooter Connectors. Five male and female connector sets: two, three, four, six pins sets, plus motor or battery connector. Makes installation of control boxes easier.
HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

INLINE FUSE BLOCK WITH 30 AMP FUSE - $7.95
plus shipping/handling

- Battery circuit protection with this inline fuse block and 30 amp fuse
HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

ADD $1 SHIPPING IF ORDER TOTAL IS LESS THAN $10

METRIC SIZE FUSE - $2.50 SET OF 5
plus shipping/handling

- 5 X 20mm Metric replacement fuse
HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

FUSEHOLDER FOR METRIC SIZE FUSE - $3.95
plus shipping/handling

- 5 X 20mm metric fuse holder
HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

FUSEHOLDER FOR AMERICAN SIZE FUSE, 3AG - $3.95
plus shipping/handling

- Universal American size replacement
Replaces impossible to get metric fuse holder and fuse
HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

FUSEHOLDER AND 25AMP FUSE, 3AG - $4.95
plus shipping/handling.

- Universal American size replacement
Replaces impossible to get metric fuse holder and fuse

X360 Left Grip Switch Assembly (no grip, sold below). $12.95
This grip switch comes with three switches: A two wire on/off light switch, A two wire momentary Horn Button, and a three wire Turn Signal switch that can also be used to control forward and reverse control boxes, if so desired (low current operation only such as reversable control boxes sold above). See grip switch normal wiring and wiring when used with reverse control boxes.

HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

X360 Left Grip (no switch assembly) for standard 7/8 $4.95

HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

ADD $1 SHIPPING IF ORDER TOTAL IS LESS THAN $10

X360 Version 1 Headlight Assembly. $19.95

Available colors choices may vary: Burgandy, Blue, Yellow, Black and Pink options. Version 1 does not have a power switch hole in addition to the Ignition Key switch hole. Includes Headlight, turn signal lights, and Guages.

HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

X360 Version 2 Headlight Assembly. $19.95

Available colors choices may vary: Burgandy, Blue, Yellow, Black and Pink options. Version 2 has a power switch hole in addition to the Ignition Key switch hole. Includes Headlight, turn signal lights, and Guages.

HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

X360 Headlight Lens. $11.95

Available colors choices may vary: Burgandy, Blue, Yellow, and Black options. Specify your desire in the message area of the order. Otherwise we will ship as available

HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

Horn for X360, 36 volt $7.95

HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

ADD $1 SHIPPING IF ORDER TOTAL IS LESS THAN $10

Ignition Switch with keys for gas or electric scooters $11.95
A 5 wire key switch used in small gas/electric scooters, pocket bikes and mini-choppers. Up to 5 wires can be used in connection but not required. Wiring connection

HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

Ignition Switch with key for X360 and other scooters $16.95
Features three connectors for either ON or OFF contact when key is turned or engaged (can be used as theft preventive in existing brake cutout circuit).

HOW TO PLACE AN ORDER: SHOPPING CART, PHONE, ETC

Ignition Switch with keys $11.95
A 2 wire key switch for larger hole switches. Snaps in place.

SCOOTER ELECTRICAL PARTS

BATTERY CHARGER, CONTROL BOX, FUSES, LIGHTS, MOTORS,
SWITCHES: IGNITION, KILL AND TOGGLE, THROTTLES

SUMMARY OF SCOOTER PARTS:

ELECTRIC SCOOTER PARTS INDEX

COMPLETE SITE INDEX OF SCOOTERS AND PARTS
AVAILABILITY OF REPLACEMENT PARTS

SCOOTER ELECTRICAL PARTS

BATTERY CHARGER, CONTROL BOX, FUSES, LIGHTS, MOTORS, SWITCHES: IGNITION, KILL AND TOGGLE, THROTTLES

SUMMARY OF SCOOTER PARTS:

ELECTRIC SCOOTER PARTS INDEX

COMPLETE SITE INDEX OF SCOOTERS AND PARTS AVAILABILITY OF REPLACEMENT PARTS

BATTERY CHARGER, CONTROL BOX, FUSES, LIGHTS, MOTORS,
SWITCHES: IGNITION, KILL AND TOGGLE, THROTTLES

COMPLETE SITE INDEX OF SCOOTERS AND PARTS
AVAILABILITY OF REPLACEMENT PARTS